| 1367 | Spring | GE | | |
| 1368 | Screw | GE | | |
| 1369-113 | Oil seal for motor applications | GE | | |
| 136X1007 | Spring | GE | | |
| 136X1009 | Gear, superseded by 135X1009 | GE | | |
| 136X1010 | Idler gear, superseded by 135X1010 | GE | | |
| 136X1021 | Dowel bushing for alignment | GE | | |
| 136X1022 | Oiler cup for lubrication | GE | | |
| 136X1030 | Gauge | GE | | |
| 136X1030-1 | Gauge oil level governor engine speed control | GE | | |
| 136X1032 | Power cylinder | GE | | |
| 136X1033 | Guard | GE | | |
| 136X1034 | Spring guard seal ring | GE | | |
| 136X1036-1 | End rod power piston contro governor diesel engine | GE | | |
| 136X1037 | Seal oil inner governor engine speed control | GE | | |
| 136X1038 | Seal oil outer governor engine speed control | GE | | |
| 136X1038PRD | Seal | GE | | |
| 136X1039 | Compensating needle valve for power cylinder | GE | | |
| 136X1040 | Base control governor diesel engine | GE | | |
| 136X1041 | Ring oil seal power case to base control governor | GE | | |
| 136X1041-1 | Ring o oil seal base to case governor diesel engin | GE | | |
| 136X1042 | Shaft drive with bearing and oil seal control | GE | | |
| 136X1043 | Shaft drive regulating governor diesel engine | GE | | |
| 136X1044 | Bearing ball drive shaft governor engine speed con | GE | | |
| 136X1045 | Seal oil drive shaft governor woodward diesel engi | GE | | |
| 136x1046 | Retainer | GE | | |
| 136X1047 | Drive shaft retainer | GE | | |
| 136X1052 | Piston governor engine control diesel engine | GE | | |
| 136X1053 | Seat spring | GE | | |
| 136X1054 | Stud , idler gear | GE | | |
| 136X1055 | Piston buffer control governor diesel engine | GE | | |
| 136X1056 | Seat spring buffer piston control governor diesel | GE | | |
| 136X1057 | Plug , buffer piston opening | GE | | |
| 136X1060 | Case , solenoid | GE | | |
| 136X1061 | Plug , plager stop | GE | | |
| 136X1062 | Coil electrical solenoid control governor diesel e | GE | | |
| 136X1062-1 | Coil solenoid 74 volt | GE | | |
| 136X1063 | Plunger , solenoid | GE | | |
| 136X1064 | Rod , power piston tail | GE | | |
| 136X1065 | Guide with bushings and pin | GE | | |
| 136X1067 | General pin for mechanical applications | GE | | |
| 136X1068 | Guide bushing for mechanical assemblies | GE | | |
| 136X1069 | Washer for solenoid assembly | GE | | |
| 136X1071 | Rod , solenoid plunger | GE | | |
| 136X1072 | Switch low water signal control governor woodward | GE | | |
| 136X1072-1 | Switch toggle low water pressure control governor | GE | | |
| 136X1074 | Clamp for switch bracket | GE | | |
| 136X1078 | Cover , wire | GE | | |
| 136X1079 | Plate | GE | | |
| 136X1084 | Body | GE | | |
| 136X1085 | Plunger | GE | | |
| 136X1086-1 | Washer , seal | GE | | |
| 136X1087 | Nut , seal retaining | GE | | |
| 136X1088 | Sleeve retaining | GE | | |
| 136X1089 | Seat , spring | GE | | |
| 136X1091 | Bushing | GE | | |
| 136X1093 | Bushing , regulating | GE | | |
| 136X1094 | Retaining , regulating bushing | GE | | |
| 136X1095 | Collar , retainer spring , 0.360 in long | GE | | |
| 136X1096 | Bearing, rep. by 136x1096-1 | GE | | |
| 136X1096-1 | Bearing thrust control governor woodward | GE | | |
| 136X1097 | Stud , drive gear | GE | | |
| 136X1102 | Pin,pilot valve to lower floating lever | GE | | |
| 136X1103-1 | Cup , with screw , solenoid | GE | | |
| 136X1107 | Head , overriding cylinder | GE | | |
| 136X1108 | Indicator control multiple load engine control | GE | | |
| 136X1109 | Piston , overriding | GE | | |
| 136X1111 | Collar , spring | GE | | |
| 136X1112 | Spacer , load control | GE | | |
| 136X1114 | Ring,retaining,load control pilot valve | GE | | |
| 136X1115 | Plunger pilot valve control governor diesel engine | GE | | |
| 136X1119 | Pin , adjustable fulcrum | GE | | |
| 136X1122 | Knob , adjusting screw | GE | | |
| 136X1123 | Pin , adjusting screw | GE | | |
| 136X1125 | Eccentric | GE | | |
| 136X1128 | Cylinder power control governor diesel engine | GE | | |
| 136X1129 | Piston , with stop pin , power | GE | | |
| 136X1131 | Lever , power piston | GE | | |
| 136X1132 | Screw , adjustable fulcrum | GE | | |
| 136X1133 | Link upper and lower floating levers | GE | | |
| 136X1134 | Spacer , link | GE | | |
| 136X1135 | Pin , upper link to lever , 0.984 in lg | GE | | |
| 136X1138 | Scale , speed indicator | GE | | |
| 136X1139-1 | Screw scale mounting , no 10-32 , 3/8 in | GE | | |
| 136X1140 | Pivot spike connection (also listed as Alco 36628-503, EMD 8452881) | GE | | |
| 136X1140-1 | Link pivot pin , 1.156 in lg | GE | | |
| 136X1141 | Pin , headed , 3/16 in dia,61/64 in long | GE | | |
| 136X1142 | Pin , lower link to lever , 0.734 in lg | GE | | |
| 136X1145 | Pin shutdown plunger diesel engine control governo | GE | | |
| 136X1149 | Piston , oil failure | GE | | |
| 136X1151 | Plunger oil failure control governor woodward | GE | | |
| 136X1152-1 | Diaphragm lubrication oil failure governor woodwar | GE | | |
| 136X1152-2 | Diaphragm lwp | GE | | |
| 136X1153-1 | Washer , diaphragm | GE | | |
| 136X1156 | Side plate cover for GE equipment | GE | | |
| 136X1157 | Glass governor engine control diesel engine genera | GE | | |
| 136X1158 | Dial for load control rheostat | GE | | |
| 136X1162-2 | Rotary servo, new design for GE systems | GE | | |
| 136X1163-1 | End plate for GE equipment | GE | | |
| 136X1164-1 | Black plate for GE applications | GE | | |
| 136X1166 | Seal oil control governor diesel engine | GE | | |
| 136X1166-1 | Oil seal for GE systems | GE | | |
| 136X1169-1 | Vane insert for GE equipment | GE | | |
| 136X1171 | Needle bearing for GE applications | GE | | |
| 136X1173 | Commutator with wiring for GE systems | GE | | |
| 136X1175 | Spacer for commutator assembly | GE | | |
| 136X1176 | Plate for commutator mounting | GE | | |
| 136X1177 | Bracket indicator with bush excitation control gov | GE | | |
| 136X1178 | Brush drive shaft for GE systems | GE | | |
| 136X1179 | Pin for brush drive shaft | GE | | |
| 136X1180 | Spring governor engine control diesel engine gener | GE | | |
| 136X1181 | Retainer for lead wire | GE | | |
| 136X1182 | Spacer for retainer assembly | GE | | |
| 136X11825 | Screw,fuel limiter system,no8-32,3/8in | GE | | |
| 136X1183 | Plug for load control holes | GE | | |
| 136X1188 | Block for retainer assembly | GE | | |
| 136X1190 | Plunger relief valve control governor diesel engin | GE | | |
| 136X1191 | Supply valve sleeve for GE locomotives | GE | | |
| 136X1198 | Retaining ring for GE locomotives | GE | | |
| 136X1201 | Ball arm for GE locomotives | GE | | |
| 136X1202 | Bearing ball governor engine control diesel engine | GE | | |
| 136X1203 | Ball arm pin for GE locomotives | GE | | |
| 136X1204 | Ring ballhead oil seal control governor diesel eng | GE | | |
| 136X1204-1 | O-ring for ballhead oil seal in GE locomotives | GE | | |
| 136X1205 | Coupling with torsion spring for centering in GE locomotives | GE | | |
| 136X1206 | Bearing ball single row ballhead ball governor eng | GE | | |
| 136X1207 | Bushing pilot valve control governor diesel engine | GE | | |
| 136X1208 | Lock washer, 5/16 inch for GE locomotives | GE | | |
| 136X1209 | Thrust bearing for GE locomotives | GE | | |
| 136X1210 | Speeder spring seat for GE locomotives | GE | | |
| 136X1211 | Pilot valve plunger for GE locomotives | GE | | |
| 136X1213 | Plug with stop pin, 0.489 inch wide for GE locomotives | GE | | |
| 136X1215 | Sleeve with bushings terminal overspeed governor | GE | | |
| 136X1219 | Latch reset overspeed governor diesel engine gener | GE | | |
| 136X1222-1 | Bracket with bush reset button overspeed governor | GE | | |
| 136X1223 | Pin pivot reset latch overspeed governor | GE | | |
| 136X1225 | Tubing | GE | | |
| 136X1231 | Shaft terminal overspeed governor diesel engine | GE | | |
| 136X1232 | Plug drive overspeed governor diesel engine | GE | | |
| 136X1238 | Thrust bearing for GE locomotives | GE | | |
| 136X1239 | Plunger | GE | | |
| 136X1245 | Pin for GE locomotives | GE | | |
| 136X1246 | Ballarm for GE locomotives | GE | | |
| 136X1256 | HEX plug, 5/8 inch-18 for GE locomotives | GE | | |
| 136X1257 | Bushing for speed adjusting pilot valve in GE locomotives | GE | | |
| 136X1258 | Bushing | GE | | |
| 136X1270 | Ballhead with ballarms | GE | | |
| 136X1271 | Ballhead with fin plate and cover control | GE | | |
| 136X1272 | Plug with stop pin , 0.614 in wide | GE | | |
| 136X1283 | Collar | GE | | |
| 136X1291 | Bearing ball governor engine control diesel engine | GE | | |
| 136X1306 | Bearing ball governor | GE | | |
| 136X1337 | Cap , adapter | GE | | |
| 136X1338 | Gasket cap governor drive diesel engine | GE | | |
| 136X1423 | Plate , orifice | GE | | |
| 136X1424 | Washer , 0.0360 in OD | GE | | |
| 136X1430 | Screw , power piston stop , no 10-32 | GE | | |
| 136X1431 | Tubing governor engine control diesel engine gener | GE | | |
| 136X1458 | Bushing , speed adjusting , pilot valve | GE | | |
| 136X1527 | Resistor pack | GE | | |
| 136X1527-2 | Resistor , exciter field | GE | | |
| 136X1530 | Valve with sleeve plunger stop sleeve pin and rele | GE | | |
| 136X1532-2 | Case manual overspeed lockout overspeed governor | GE | | |
| 136X1534 | Valve by-pass control governor diesel engine | GE | | |
| 136X1541 | Bush terminal overspeed governor | GE | | |
| 136X1562 | Indicator , vane servo | GE | | |
| 136X1569 | Reset | GE | | |
| 136X1573 | Piston, r/b 132x1573-1 | GE | | |
| 136X1573-1 | Plunger | GE | | |
| 136X1579 | Dowel | GE | | |
| 136X1583 | Rod straight spring guide overspeed governor diese | GE | | |
| 136X1585 | Ring retainer spring guide overspeed governor | GE | | |
| 136X1589-1 | Case with check valves and accumulator piston powe | GE | | |
| 136X1590 | Casing power control governor woodward diesel engi | GE | | |
| 136X1594 | Bush pilot valve load control control governor die | GE | | |
| 136X1598 | Diaphragm governor engine control diesel engine GE | GE | | |
| 136X1611 | Diaphragm | GE | | |
| 136X1621 | Valve overspeed fuel shut-off control governor | GE | | |
| 136X1624 | Diaphragm overspeed fuel shut-off engine control | GE | | |
| 136X1627 | Case shutdown control governor woodward | GE | | |
| 136X1628 | Cover , switch | GE | | |
| 136X1629 | Plate , switch | GE | | |
| 136X1632 | Block ratio lever water shut down mechanism engine | GE | | |
| 136X1633 | Strap , clamp | GE | | |
| 136X1635 | Lever with diaphragm seat ratio engine control | GE | | |
| 136X1636-1 | Bearing needle engine control governor diesel engi | GE | | |
| 136X1637 | Pin engine control governor diesel engine | GE | | |
| 136X1638 | Washer engine control governor diesel engine | GE | | |
| 136X1639 | Washer diaphragm engine control governor diesel | GE | | |
| 136X1640 | Retainer , spring | GE | | |
| 136X1642-1 | Pin , adjusting | GE | | |
| 136X1644 | End plug | GE | | |
| 136X1646 | Plug , bushing | GE | | |
| 136X1648 | Pin , plunger end | GE | | |
| 136X1649 | Tube wiring regulating governor woodward diesel en | GE | | |
| 136X1650 | Sleeve | GE | | |
| 136X1656 | Strip , terminal,2 terminal connections | GE | | |
| 136X1657 | Valve with spring and pin floating lever control | GE | | |
| 136X1658 | Diaphragm governor engine control diesel engine GE | GE | | |
| 136X1681 | Plug ball check control governor diesel engine | GE | | |
| 136X1683 | Bushing | GE | | |
| 136X1686 | Diaphragm oil failure control governor diesel engi | GE | | |
| 136X1691 | Screw , adjusting pressure range | GE | | |
| 136X1694 | Terminal | GE | | |
| 136X1694-1 | Nut , adjusting , 1/4 in-28 | GE | | |
| 136X1698 | Cover assembly with oil filler cup gasket and bush | GE | | |
| 136X1700 | Gavernor | GE | | |
| 136X1700-REMAN | Governor | GE | | |
| 136X1701 | Governor control diesel engine | GE | | |
| 136X1703 | Column assembly control governor diesel engine | GE | | |
| 136X1706 | Bracket , solenoid | GE | | |
| 136X1707 | Connector plug electrical with wiring control | GE | | |
| 136X1711 | Column with inserts bushings and pin control | GE | | |
| 136X1714 | Valve , load control pilot | GE | | |
| 136X1722 | Screw , adjusting floating lever | GE | | |
| 136X1724 | Fulcrum for power piston | GE | | |
| 136X1727 | Screw , power piston stop , no 10-32 | GE | | |
| 136X1728 | Diaphragm assembly lubricating oil shutdown | GE | | |
| 136X1729 | Plunger oil failure control governor diesel engine | GE | | |
| 136X1731-1 | Diaphragm oil pressure failure governor engine | GE | | |
| 136X1731-2 | Diaphragm oil spacer brushing | GE | | |
| 136X1732 | Spacer for oil failure detection | GE | | |
| 136X1733 | Piston | GE | | |
| 136X1734 | Diaphragm | GE | | |
| 136X1734-1 | Diaphragm oil failure governor engine control dies | GE | | |
| 136X1736 | Seal plate | GE | | |
| 136X1740-5R | Governor | GE | | |
| 136X1740-7R | Governor rebuilt | GE | | |
| 136X1741 | Side plate | GE | | |
| 136X1743 | Spring and holder , contact | GE | | |
| 136X1744 | Filter with plug gasket and "o" rings control | GE | | |
| 136X1746 | Filter and plug | GE | | |
| 136X1747 | Case for filter and plug | GE | | |
| 136X1752 | Sleeve rotating consisting of shutdown rod ballhea | GE | | |
| 136X1753 | Rod | GE | | |
| 136X1753-1 | Rod shutdown diesel engine control governor | GE | | |
| 136X1754 | Shutdown | GE | | |
| 136X1755 | Water box with guide pin | GE | | |
| 136X1757 | Check valve | GE | | |
| 136X1758 | Plug and filter screen for check valve | GE | | |
| 136X1760 | Orifice case | GE | | |
| 136X1761-1 | Retaining ring | GE | | |
| 136X1763 | Sleeve | GE | | |
| 136X1764 | Nut for 1/4 inch OD tube | GE | | |
| 136X1765 | Retaining nut | GE | | |
| 136X1805-1 | Shutdown rod nut, no. 8-32, reduced HEX | GE | | |
| 136X1807 | Overspeed clamp bracket | GE | | |
| 136X1812 | Pressure sensor body | GE | | |
| 136X1814 | Piston sleeve | GE | | |
| 136X1816 | Diaphragm assembly | GE | | |
| 136X1820 | Bellows output strap | GE | | |
| 136X1821 | Retainer ring | GE | | |
| 136X1822 | Ring "o" seal bellow assembly 1.254 inches outside | GE | | |
| 136X1822-1 | Preformed packing | GE | | |
| 136X1823 | Bellows spacer | GE | | |
| 136X1825 | Screw for bellows assembly to case, no. 8-32 | GE | | |
| 136X1826 | Gasket | GE | | |
| 136X1827 | Accentric | GE | | |
| 136X1828 | Pin , drilled | GE | | |
| 136X1829 | Cam , fuel limit | GE | | |
| 136X1830 | Screw , lever adjusting | GE | | |
| 136X1831 | Pivot assembly | GE | | |
| 136X1832-1 | Bracket fuel limiter linkage governor diesel engin | GE | | |
| 136X1833 | Lever , feedback | GE | | |
| 136X1834 | Piston | GE | | |
| 136X1835 | Valve , shutdown pilot | GE | | |
| 136X1836-1 | Lever floating engine control governor diesel engi | GE | | |
| 136X1837 | Pin , tailroad | GE | | |
| 136X1838 | Pin , bellcrank pivot | GE | | |
| 136X1840-1 | Bellcrank , limiter | GE | | |
| 136X1841 | Lever , limit | GE | | |
| 136X1842 | Pin , limit , lever pivot | GE | | |
| 136X1844 | Pin , pivot | GE | | |
| 136X1845 | Arm , cam follower | GE | | |
| 136X1848 | Bushing , shutdown rod | GE | | |
| 136X1849 | Screw | GE | | |
| 136X1851 | Block , adjusting | GE | | |
| 136X1852 | Adjusting block for pivot mechanism | GE | | |
| 136X1853 | Pivot pin link for mechanical connections | GE | | |
| 136X1854 | Cap assembly for pivot link | GE | | |
| 136X1855 | Plug for diaphragm with headed pin | GE | | |
| 136X1892 | Water box diaphragm clamp plate | GE | | |
| 136X1896 | Diaphragm cap for sealing applications | GE | | |
| 136X1897 | Spring seat component | GE | | |
| 136X1898 | Diaphragm plug for sealing | GE | | |
| 136X1899-1 | Nameplate for identification | GE | | |
| 136X1907 | Screw for end plate to housing and divider | GE | | |
| 136X1918-2 | Terminal for electrical connections | GE | | |
| 136X1928 | Locking nut for bulkhead union | GE | | |
| 136X1942 | Load control pilot bushing | GE | | |
| 136X1943 | Connector assembly with wiring governor engine | GE | | |
| 136X1948 | Diaphragm, rep. by 136x1948-3 | GE | | |
| 136X1948-2 | Diaphragm | GE | | |
| 136X1948-3 | Diaphragm water pressure engine control governor d | GE | | |
| 136X1948-4 | Diaphragm | GE | | |
| 136X1951 | Adjusting block component | GE | | |
| 136X1952 | HEX socket head screw, no. 8-32, 7/8 in | GE | | |
| 136X1953 | Restoring spring component | GE | | |
| 136X1954 | Limiter valve seat component | GE | | |
| 136X1956 | Fuel limiter piston component | GE | | |
| 136X1957 | Pin | GE | | |
| 136X1958 | Seat , sensor spring , upper | GE | | |
| 136X1959 | Seat , sensor spring , lower | GE | | |
| 136X1963 | Gasket connector plug control governor diesel engi | GE | | |
| 136X1964 | Block , terminal,3 terminal connections | GE | | |
| 136X1966-1 | No. 6-32 terminal block mounting screw | GE | | |
| 136X1967 | Washer for terminal block and terminal strip | GE | | |
| 136X1968 | Pin , fuel limiter system , 0.125 in dia | GE | | |
| 136X1969 | Clamp strap screw, 1/4 in-28, 1 1/8 in | GE | | |
| 136X1971 | HEX socket pipe plug, 1/16 in-27 | GE | | |
| 136X1972 | Insert , threaded , 5/16 in-24 , 5/8 in | GE | | |
| 136X1973 | Lever with adjusting block and eccentric | GE | | |
| 136X1974 | Lever , floating | GE | | |
| 136X1976 | Pin , movable fulcrum | GE | | |
| 136X1977 | Eccentric | GE | | |
| 136X1979 | Plain washer, 1/4 in | GE | | |
| 136X1981 | Dowel , 1/4 in dias , by 3/4 in lg | GE | | |
| 136X1982 | Resistor with commutator and shaft | GE | | |
| 136X1983 | Spacer , resistor pack | GE | | |
| 136X1984 | No. 8-32 screw for resistor and spacer mounting | GE | | |
| 136X1987 | Gasket plug filter case engine control governor | GE | | |
| 136X1989 | Nut plunger pilot valve control governor diesel | GE | | |
| 136X1991 | Bellows assembly for various applications | GE | | |
| 136X1993 | HEX socket head screw, 1/4 in-28, 3/4 in long | GE | | |
| 136X1994 | HEX socket head screw, 1/4 in-28, 1 1/4 in long | GE | | |
| 136X1996 | Indicator for multiplying load control | GE | | |
| 136X1997-1 | Set screw for micro switch, no. 8-32, 1 in long | GE | | |
| 136X1998-1 | Self-locking nut, no. 8-32 | GE | | |
| 136X1999-1 | Bulkhead union for piping applications | GE | | |
| 136X2001 | Lock-nut screw for securing connections | GE | | |
| 136X2006 | Plate connector clamping plug control governor | GE | | |
| 136X2007-1 | Screw fillet head no.4 x 1/4 inch long connector t | GE | | |
| 136X2008-1 | Washer lock no.4 plug control governor diesel engi | GE | | |
| 136X2009-1 | Shutdown plunger for safety systems | GE | | |
| 136X2011 | Shutdown piston stop, 17/32 in | GE | | |
| 136X2012 | Plug for column, plunger hole | GE | | |
| 136X2013 | Diaphragm assembly for lube oil shutdown | GE | | |
| 136X2014 | Bushing for oil failure valve | GE | | |
| 136X2016 | Low water pressure shutdown component | GE | | |
| 136X2018 | Plug for shutdown case, plunger hole | GE | | |
| 136X2021 | Bushing for various applications | GE | | |
| 136X2022 | Bearing for various applications | GE | | |
| 136X2024 | Flat washer | GE | | |
| 136X2026 | HEX head screw, 1/4 in-28, 2 1/4 in long | GE | | |
| 136X2034-1 | Screw | GE | | |
| 136X2039 | Shaft terminal overspeed governor | GE | | |
| 136X2042 | Plug overspeed governor diesel engine | GE | | |
| 136X2045-1 | Governor control diesel engine | GE | | |
| 136X2046 | Speed adjusting shaft | GE | | |
| 136X2047 | Lever for speed adjusting | GE | | |
| 136X2048 | Roll pin for securing components | GE | | |
| 136X2050 | Overspeed unit | GE | | |
| 136X2056 | Spring wire pin | GE | | |
| 136X2057 | Fork , spring | GE | | |
| 136X2058 | Pin | GE | | |
| 136X2059 | Spring | GE | | |
| 136X2061 | Bushing for various applications | GE | | |
| 136X2062 | Shim with sleeve relief valve overspeed governor | GE | | |
| 136X2063 | Plunger solenoid overspeed governor | GE | | |
| 136X2064 | Spring , relief valve | GE | | |
| 136X2066 | Spring | GE | | |
| 136X2067 | Gasket relief valve overspeed governor diesel engi | GE | | |
| 136X2068 | Plug for various applications | GE | | |
| 136X2069 | Bush assembly with shutdown valve and plugs | GE | | |
| 136X2072 | Spring , pilot valve plunger | GE | | |
| 136X2081 | Lock washer, no. 6 | GE | | |
| 136X2097 | Block , adjusting | GE | | |
| 136X2101 | Bushing load control pilot | GE | | |
| 136X2104 | Lever with adjusting block and eccentric | GE | | |
| 136X2106 | Filister head screw, no. 12-24, 1/2 inch long | GE | | |
| 136X2107 | Snap ring for securing components in place | GE | | |
| 136X2108 | Spring , safety shutdown | GE | | |
| 136X2109 | Power piston | GE | | |
| 136X2112 | Telescoping piston | GE | | |
| 136X2124 | Plate mounting with straps and bimeteal strip | GE | | |
| 136X2126 | Lever with spring and pin lower floating governor | GE | | |
| 136X2131 | Link , pilot valve | GE | | |
| 136X2132 | Link , pilot valve | GE | | |
| 136X2133 | Pin for securing components in locomotive assemblies | GE | | |
| 136X2134 | Plunger shutdown diesel engine control governor | GE | | |
| 136X2136 | Plug assembly | GE | | |
| 136X2137 | Bracket , switch mounting | GE | | |
| 136X2138 | Rod end assembly (latest design) | GE | | |
| 136X2139 | Piston with rod control governor diesel engine | GE | | |
| 136X2149 | Scale , piston gap,spring guard mounted | GE | | |
| 136X2165-3 | Governor dash 7 | GE | | |
| 136X2165-3-RR | Governor dash 7 | GE | | |
| 136X2165-3-UX | Governor dash 7 | GE | | |
| 136X2165-3-UX-W12 | Governor dash 7 | GE | | |
| 136X2178 | Connector with wiring (16 pin connector) | GE | | |
| 136X2179 | Valve assembly | GE | | |
| 136X2181 | Lever , over riding solenoid | GE | | |
| 136X2182 | Bracket , switch mounting | GE | | |
| 136X2183 | Mounting plate for micro switch | GE | | |
| 136X2187 | Lever assembly with bracket, spring, and o-ring | GE | | |
| 136X2188 | Lever assembly with switch bracket and spring | GE | | |
| 136X2189 | Wire assembly with terminal | GE | | |
| 136X2190-1 | Micro switch | GE | | |
| 136X2196-1 | Governor diesel engine control woodward | GE | | |
| 136X2198 | 1/8 inch nipple fitting | GE | | |
| 136X2199 | General fitting | GE | | |
| 136X2200 | Oil level gauge for power case | GE | | |
| 136X2201 | Tubing component | GE | | |
| 136X2203 | Spring guard | GE | | |
| 136X2208 | Plug o-ring | GE | | |
| 136X2218 | Base | GE | | |
| 136X2222 | Ballhead with ball arms and retaining pin | GE | | |
| 136X2223 | Gear oil pump drive governor engine overspeed dies | GE | | |
| 136X2224 | Ballhead | GE | | |
| 136X2228 | Retaining ring | GE | | |
| 136X2229 | HEX jam nut, 1/4 inch-28 | GE | | |
| 136X2231 | Diaphragm assembly | GE | | |
| 136X2243 | Bushing for speed adjusting pilot valve | GE | | |
| 136X2244 | Spring retainer for GE locomotives | GE | | |
| 136X2245UX | Governor dash 8 | GE | | |
| 136X2246 | Lever with adjusting block and eccentric for GE locomotives | GE | | |
| 136X2247 | Adjusting screw for GE locomotives | GE | | |
| 136X2248 | Adjusting block screw for GE locomotives | GE | | |
| 136X2250-2 | Overspeed gov | GE | | |
| 136X2250-2-UX | Os governor | GE | | |
| 136X2252 | Governor overspeed complete diesel engine | GE | | |
| 136X2271 | Indicator screw, no. 10-32, 3/8 in long for GE locomotives | GE | | |
| 136X2317 | Gasket, governor | GE | | |
| 136X2318 | 1/4 inch sealing washer for GE locomotives | GE | | |
| 136X2322 | Gear oil pump idler governor engine overspeed dies | GE | | |
| 136X2323 | Stud idler gear governor engine overspeed diesel | GE | | |
| 136X2332 | Terminal lever for GE locomotives | GE | | |
| 136X2333 | Bushing for GE locomotives | GE | | |
| 136X2334 | Socket head cap screw, no. 10-32, 7/8 in long for GE locomotives | GE | | |
| 136x2335 | Overspeed governor for GE locomotives | GE | | |
| 136X2335-UX | Overspeed governor auto reset | GE | | |
| 136X2336 | Bracket for GE locomotives | GE | | |
| 136X2337 | Pin for GE locomotives | GE | | |
| 136X2338 | Strut for GE locomotives | GE | | |
| 136X2339 | Spring seat for GE locomotives | GE | | |
| 136X2341 | Floating lever for GE locomotives | GE | | |
| 136X2342 | Cover for GE locomotives | GE | | |
| 136X2343 | Low speed guide plug for GE locomotives | GE | | |
| 136X2344 | Case | GE | | |
| 136X2346 | Screw , drive , no 2 by 1/8 in long | GE | | |
| 136X2348 | Shaft , terminal | GE | | |
| 136X2349 | Plate bearing | GE | | |
| 136X2351 | Tubing | GE | | |
| 136X2390-UX | Governor dash 8 | GE | | |
| 136X2420 | Woodward governor (#8572-813) | GE | | |
| 136X93 | Railway journal bearing wedge | GE | | |